Combi Flash 7650 Series Bedienungsanleitung Seite 31
- Seite / 159
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Section 2 Preparation
2-11
If an optional waste cap is not used, ensure the waste lines are
secured so they drain into the waste container. Secure the
Waste Level Sense air tubing so its outlet is at least two inches
(5 cm) below the container’s maximum level. Seal the
container opening to avoid solvent vapors.
2.8 Optional External Gas
The Torrent has an internal air pump that provides
compressed air for solvent and waste level sensing, and
column/cartridge purging. Optionally, the system can deliver a
compressed gas instead of air. Inert or other gases may be
more suitable than air for some applications.
If ambient air is compatible with your solvents and waste,
simply leave the GAS INLET port open.
If you want to use a gas instead of air, connect user-supplied
1
8" I.D. tubing to the GAS INLET port. Connect the other end
to the user-supplied compressed gas. The external compressed
gas should be dry, filtered, and regulated to 2–5 psi (0.14–0.34
atm, 13.8–34.5 kPa).
2.9 Connect and Route Drain Line
WARNING
Risk of fire or equipment damage. Failure to connect drain lines
may allow organic solvents to pool in unsafe areas, creating a
potential for dangerous levels of flammable vapors. Improper
draining may damage the instrument’s internal components.
The Torrent has a front-mounted drip tray. There is a drain
connection under the left side of the tray. Connect
user-supplied tubing to this drain and route it to a suitable
waste fluid collection container.
- CombiFlash Tor re n t 1
- User Manual 1
- 3. Operation 4
- 4. User Help Reference 4
- 5. Remote Interfaces 5
- 6. Maintenance 6
- 1.3 Operating Overview 9
- 1.4 Specifications 10
- Section 1 Introduction 11
- 1.6 Safety 15
- Warnings and Cautions 18
- Symboles de sécurité 18
- Advertencias y Precauciones 19
- 2.2 Instrument Location 22
- 2.3 Connect Power 22
- NSTALL OPTIONAL EQUIPMENT 23
- 2.5 Position the Torrent 24
- 2.6 Connect Solvent Lines 25
- (Solvent B) 26
- 2 turn using a wrench 27
- 8-inch fittings from the 28
- 2.8 Optional External Gas 31
- Waste (NO) 33
- In (Common) 33
- Drop Former (NC) 33
- ETWORK CONFIGURATION 34
- Section 2 Preparation 35
- From top of diverter valve 42
- Connect ELSD 43
- Standoffs (place over 45
- Disconnect 46
- 2.11 Grounding 48
- 2.12 Turn on Power 48
- 2.13 Configure the Torrent 48
- B priming pump 50
- 2.13.2 User Preferences 51
- EMOTE INTERFACES. Do not 52
- RIME B button 57
- Section 3 Operation 65
- 3.2 Sample Preparation 66
- 3.2.2 Solid Samples 67
- OOLS>MANUAL CONTROL) 68
- 4 turn to seal the fittings 71
- 3.4 Start a Default Method 72
- 3.4.1 Syringe Injection 74
- 3.5 During the Run 77
- Section 4 User Help Reference 81
- 4.1.2 Method File 82
- 4.2 PeakTrak Menu Options 83
- 4.2.1 File 84
- 4.2.1.1 New 84
- 4.2.1.2 Open 84
- 4.2.1.3 Manage Files 84
- 4.2.1.4 Set Data Path… 84
- [4.2.3.5]” command instead 85
- [4.3.5] window. From 85
- [4.2.1.9] menu command 86
- [4.3.7] window 87
- [4.3.8] 87
- [4.3.9] 87
- 4.2.3.4 Auto Zero 88
- 4.2.3.5 Edit defaults 88
- 4.2.3.6 Configuration 88
- 4.2.3.7 Set Password 88
- 4.2.3.8 User Management 88
- 4.3 PeakTrak Windows 90
- 4.3.1.1 Gradient Plot 91
- 4.3.1.2 Run Settings 91
- 4.3.1.5 Peak Collection Data 94
- 4.3.2 Method Editor 95
- 4.3.2.1 Button bar 95
- [4.3.10] settings 96
- [ON-LINE]. The 97
- [4.3.10] 98
- [4.4.5] 98
- 4.3.2.5 Peak Collection 99
- 4.3.2.6 Peak Detection 100
- 4.3.3 Gradient Optimizer 101
- [4.2.1.2] and SAVE 102
- [4.2.1.2] 103
- [4.2.3.1] menu command. The 104
- [4.2.3.3] from the 105
- [4.2.3.2] menu command. The 105
- [4.4.10] 106
- [4.2.3.3] menu 107
- [4.3.10.4] 107
- [ON-LINE] 107
- [4.3.11] 108
- [4.4.11] 108
- [4.3.2.5] settings on the 108
- ETWORK PRINTING feature 110
- 4.3.10.4 Fraction Collector 111
- 4.3.11 Set Password 112
- 4.3.12 User Management 113
- ON-LINE]) 114
- 4.4.2 Editing a method 117
- [4.4.5] topic for more 118
- [4.3.10] window 118
- [ON-LINE] for actual 119
- [4.2.1.9] 122
- [4.3.5] 123
- [4.2.3.5] menu command 123
- [4.4.2] 123
- [4.3.1] and 124
- [4.3.2] window 125
- [4.3.3]). Note the 126
- [4.3.5] window is displayed 127
- [4.3.1] 127
- [4.3.10.2] settings 128
- [4.4.7] help topic 129
- [4.3.9] window by 130
- [ON-LINE] topic 131
- CombiFlash To r re n t 133
- 5.1.1 Network PC Access 134
- 5.1.2 Network Printing 134
- Section 5 Remote Interfaces 135
- 5.2 Direct Connection 136
- 5.2.2 Windows Vista Settings 138
- 5.2.3 Windows XP Settings 140
- 5.2.4 Windows 2000 Settings 142
- 5.3 Direct Printing 144
- 6.2 Preventive Maintenance 146
- 6.3 Cleaning 147
- 6.4 Tubing Inspection 148
- 6.5 Flow Cell Cleaning 148
- Section 6 Maintenance 149
- Solvent Description 153
- DECLARATION OF CONFORMITY 157
Verwandte Produkte und Handbücher für Kinderwagen Combi Flash 7650 Series
(40 Seiten)
Kinderwagen Combi DK-5 4050 Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Kinderwagen Combi 7100 Series Spezifikationen
(104 Seiten)
(104 Seiten)
Kinderwagen Combi Strolee Bedienerhandbuch
(80 Seiten)
(80 Seiten)
Kinderwagen Combi 2800 Bedienungshandbuch
(40 Seiten)
(40 Seiten)
Kinderwagen Combi Flash EX Spezifikationen
(28 Seiten)
(28 Seiten)
Kinderwagen Combi Flash EX 655 Spezifikationen
(38 Seiten)
(38 Seiten)
Kinderwagen Combi Flare Bedienungsanleitung
(9 Seiten)
(9 Seiten)
Kinderwagen Combi 7720 Bedienerhandbuch
(22 Seiten)
(22 Seiten)
(60 Seiten)
Kinderwagen Combi Flash EX Spezifikationen
(50 Seiten)
(50 Seiten)
Kinderwagen Combi CATALYST Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Kinderwagen Combi Cosmo DX Betriebsanweisung
(18 Seiten)
(18 Seiten)
Kinderwagen Combi Savona TS 4000 Bedienungsanleitung
(218 Seiten)
Kinderwagen Combi Savvy Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Kinderwagen Combi Twin Cosmo Bedienungsanleitung
(12 Seiten)
(12 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern